Start with the plate and the room, not the wiring
A three-gang dimmer controls three lighting circuits from one plate, so the first decision is practical: which three groups of lights should dim together? The 3G Dimmer 120W Cross Brass is a three-gang dimmer switch finished in brass, with a diamond-cut cross-knurl knob made from solid brass. That gives you a clear starting point for a multi-gang dimming setup, but it does not tell you whether your circuits, back box or bulbs are ready for it.
Use this guide to work through the decisions in order: confirm the gang count, plan the load, check bulb compatibility, prepare the wall position, and only then hand the job to a qualified electrician. The catalog facts below are the only product details supplied; anything not stated should be verified on site or with the manufacturer before you commit.
What the catalog confirms about this dimmer
- 3G DIMMER / CROSS / 120W / BRASS: A 3G dimmer switch finished in brass. Confirms it is a three-gang dimmer, so it suits a plate that controls three lighting circuits, not a single dimmer or a simple on/off switch.

3G DIMMER / CROSS / 120W / BRASS - 3G DIMMER / CROSS / 120W / BRASS: The dimmer knob features our signature, diamond-cut, cross-knurl pattern and is made from solid brass. The brass finish and knurled knob are the visible design choices; they matter for matching other brass hardware in the room, not for electrical performance.
- 3G DIMMER / CROSS / 120W / BRASS: Catalog price: USD 122.10, comparison price USD 185.00. Gives you a current price reference before you compare it with other three-gang options or budget for a multi-gang project.
Checkpoints before you buy a three-gang dimmer
These are the questions that decide whether the 3G Dimmer 120W Cross Brass fits your project. Work through them before ordering, because a three-gang plate is harder to change later than a single switch.
- Gang count: Count the lighting circuits you want to dim separately. Three circuits need a three-gang plate; if you only need two, a 3G unit leaves one gang unused or forces you to combine circuits.
- Load per gang: The product name includes a 120W rating, but the supplied record does not break that down per gang or state a total. Treat 120W as the figure to verify with the manufacturer or your electrician rather than assuming it applies to each gang.
- Bulb compatibility: The supplied information does not confirm which bulb types or dimming protocols this dimmer supports. Check the bulbs you plan to use, especially LEDs, against the manufacturer's compatibility information before installation.
- Wall position and back box: A three-gang plate needs a back box with enough room for three dimmer mechanisms and the wiring. The supplied record does not give dimensions, so measure the existing box and confirm fit before you order.
- Finish matching: Brass is a warm metal finish. If the room already has brass sockets, cabinet hardware or lighting, this dimmer will sit naturally alongside them; if everything else is steel or black, decide whether the contrast is intentional.
A sensible order for the three-gang job
This sequence keeps the electrical decisions separate from the finish and fit decisions. It does not replace local wiring rules or a qualified electrician's assessment.
- Map the three circuits: Label which lights each gang will control and note whether any circuit serves a room with different bulb types. This prevents surprises when you check compatibility.
- Confirm the load: Add up the wattage of the bulbs on each circuit and compare it with the 120W figure in the product name. Because the supplied record does not state whether 120W is per gang or total, ask the manufacturer or your electrician to confirm before wiring.
- Check bulb compatibility: The supplied information does not list supported bulb types. Test or verify the exact bulbs you intend to use, and keep the packaging or specification sheet for reference.
- Measure the back box: Confirm the existing box can accept a three-gang dimmer plate and that there is clearance behind the plate for the dimmer bodies. If the box is too shallow or too small, plan the wall work before ordering.
- Book the electrician: Dimmer installation involves mains wiring. Use a qualified electrician who can verify the circuit, the earth connection and the load against the manufacturer's instructions.
- Fit and test: After installation, test each gang separately with the bulbs you plan to use. If a gang behaves unexpectedly, stop and have the electrician check the circuit rather than swapping bulbs repeatedly.
Where the 120W rating fits into load planning
The 120W figure in the product name is the most important number to understand before you buy, and it is also the one the supplied record explains least. It may refer to a maximum load for the dimmer, but the record does not state whether that is per gang, total across all three gangs, or specific to certain bulb types. Do not assume it is a per-gang allowance without confirmation.
For a three-gang setup, the safe approach is to calculate the wattage of each circuit and the combined total, then put both figures in front of the manufacturer or your electrician. If your planned bulbs exceed the confirmed limit, reduce the number of bulbs on the dimmer or split the circuits rather than relying on the dimmer to cope. This is also the point to check whether your bulbs are dimmable at all; the supplied information does not confirm bulb compatibility.
Brass versus other finishes in a multi-gang setup
Finish is the main visible difference between this dimmer and other Cross dimmers in the range. The electrical decisions above stay the same; the choice is about how the plate sits with the rest of the room.
- Brass: Warm, traditional metal tone. The 3G Dimmer 120W Cross Brass uses solid brass for the knurled knob, so the finish is part of the product rather than a coating. It suits rooms with brass sockets, handles or light fittings.
- Steel or black: Cooler or more graphic alternatives. If your room is mostly steel or black hardware, a brass dimmer becomes a deliberate accent; decide whether that is the look you want before ordering three gangs of it.
- Consistency across gangs: In a three-gang plate, all three knobs are visible together. Order the finish as one decision for the whole plate rather than mixing finishes across gangs.
What the supplied information does not confirm
The supplied record confirms the product type, the brass finish and the solid brass cross-knurl knob, but it does not include dimensions, back box requirements, wiring diagrams, supported bulb types, or a per-gang load breakdown. It also does not include care instructions or installation steps. Those gaps are not evidence that the product lacks these features; they simply mean you should confirm them with the manufacturer or a qualified electrician before purchase and installation.
If you need a dimmer for a single circuit, a 1G model may be a better fit; if you need four circuits, a 4G plate avoids leaving a gang unused. For a three-circuit room where the brass finish matches the existing hardware, the 3G Dimmer 120W Cross Brass is the straightforward choice once the load and bulb questions are settled.


